openpilot v0.9.6 release

date: 2024-01-12T10:13:37
master commit: ba792d576a49a0899b88a753fa1c52956bedf9e6

panda/board/boards/tres.h

@@ -0,0 +1,98 @@
+// /////////////////
+// Tres + Harness //
+// /////////////////
+
+bool tres_ir_enabled;
+bool tres_fan_enabled;
+void tres_update_fan_ir_power(void) {
+  red_chiplet_set_fan_or_usb_load_switch(tres_ir_enabled || tres_fan_enabled);
+}
+
+void tres_set_ir_power(uint8_t percentage){
+  tres_ir_enabled = (percentage > 0U);
+  tres_update_fan_ir_power();
+  pwm_set(TIM3, 4, percentage);
+}
+
+void tres_set_bootkick(BootState state) {
+  set_gpio_output(GPIOA, 0, state != BOOT_BOOTKICK);
+  set_gpio_output(GPIOC, 12, state != BOOT_RESET);
+}
+
+void tres_set_fan_enabled(bool enabled) {
+  // NOTE: fan controller reset doesn't work on a tres if IR is enabled
+  tres_fan_enabled = enabled;
+  tres_update_fan_ir_power();
+}
+
+bool tres_read_som_gpio (void) {
+  return (get_gpio_input(GPIOC, 2) != 0);
+}
+
+void tres_init(void) {
+  // Enable USB 3.3V LDO for USB block
+  register_set_bits(&(PWR->CR3), PWR_CR3_USBREGEN);
+  register_set_bits(&(PWR->CR3), PWR_CR3_USB33DEN);
+  while ((PWR->CR3 & PWR_CR3_USB33RDY) == 0);
+
+  red_chiplet_init();
+
+  // C2: SOM GPIO used as input (fan control at boot)
+  set_gpio_mode(GPIOC, 2, MODE_INPUT);
+  set_gpio_pullup(GPIOC, 2, PULL_DOWN);
+
+  // SOM bootkick + reset lines
+  set_gpio_mode(GPIOC, 12, MODE_OUTPUT);
+  tres_set_bootkick(BOOT_BOOTKICK);
+
+  // SOM debugging UART
+  gpio_uart7_init();
+  uart_init(&uart_ring_som_debug, 115200);
+
+  // SPI init
+  gpio_spi_init();
+
+  // fan setup
+  set_gpio_alternate(GPIOC, 8, GPIO_AF2_TIM3);
+
+  // Initialize IR PWM and set to 0%
+  set_gpio_alternate(GPIOC, 9, GPIO_AF2_TIM3);
+  pwm_init(TIM3, 4);
+  tres_set_ir_power(0U);
+
+  // Fake siren
+  set_gpio_alternate(GPIOC, 10, GPIO_AF4_I2C5);
+  set_gpio_alternate(GPIOC, 11, GPIO_AF4_I2C5);
+  register_set_bits(&(GPIOC->OTYPER), GPIO_OTYPER_OT10 | GPIO_OTYPER_OT11); // open drain
+  fake_siren_init();
+
+  // Clock source
+  clock_source_init();
+}
+
+const board board_tres = {
+  .board_type = "Tres",
+  .harness_config = &red_chiplet_harness_config,
+  .has_hw_gmlan = false,
+  .has_obd = true,
+  .has_spi = true,
+  .has_canfd = true,
+  .has_rtc_battery = true,
+  .fan_max_rpm = 6600U,
+  .avdd_mV = 1800U,
+  .fan_stall_recovery = false,
+  .fan_enable_cooldown_time = 3U,
+  .init = tres_init,
+  .init_bootloader = unused_init_bootloader,
+  .enable_can_transceiver = red_chiplet_enable_can_transceiver,
+  .enable_can_transceivers = red_chiplet_enable_can_transceivers,
+  .set_led = red_set_led,
+  .set_can_mode = red_chiplet_set_can_mode,
+  .check_ignition = red_check_ignition,
+  .read_current = unused_read_current,
+  .set_fan_enabled = tres_set_fan_enabled,
+  .set_ir_power = tres_set_ir_power,
+  .set_siren = fake_siren_set,
+  .set_bootkick = tres_set_bootkick,
+  .read_som_gpio = tres_read_som_gpio
+};